Miele T 4804 C Allerdry Operating Instructions Manual Download Page 61

Page: 61 / 68

Clean out airways indicator

Fluff should be removed after drying.
The

Clean out airways

indicator will

remind you to clean the filters when a
certain amount of fluff has collected
in the filters. You can decide at what
level of fluff this reminder should be
given.

You will have an idea of how often this
should be done after a few drying
programmes.

Follow the steps (

...) to

programme and store in memory.

Before you begin, ensure that:

– The tumble dryer is switched off.

– The door is closed.

Press the

Start/Stop

button and keep

it pressed in whilst carrying out steps

Switch the dryer on.

Wait until the

Start/Stop

button lights up

constantly . . .

. . . and then release the

Start/Stop

button.

Press the

Low temperature

button

eight times.

– The

Low temperature

indicator light

will flash on and off slowly once.

number

to show which option is

selected will appear in the display
alternating with the letter

Clean out airways indicator light is
deactivated

Clean out airways indicator light
comes on when there is a heavy
build-up of fluff

(the

Automatic

indicator light will also

flash once).

Factory default setting

(the

Automatic

indicator light will also

flash twice).

Clean out airways indicator light
comes on when there is only a
light build-up of fluff

(the

Automatic

indicator light will also

flash three times).

Pressing the

Start/Stop

button

switches between the options.

Switch the dryer off.

The setting you have selected is now
stored in memory. You can change it
again at any time.

To check the setting:

Carry out steps

Switch the dryer off after step

Programmable functions

Summary of Contents for T 4804 C Allerdry





































































Search results

Summary of Contents for T 4804 C Allerdry

Reviews:

Related manuals for T 4804 C Allerdry

Brands by name

Popular brands

Miele T 4804 C Allerdry, Operating Instructions Manual

Search results

Summary of Contents for T 4804 C Allerdry

Reviews:

Related manuals for T 4804 C Allerdry

Brands by name

Popular brands