manualshive.com logo in svg

Miele T 4659 Ci, Operating Instructions Manual

Share
Download
Miele T 4659 Ci Operating Instructions Manual Download Page 39

Aligning the machine

^

Turn the 4 screw feet to adjust the
dryer to the correct height and level.

Longer screw feet are available as
an optional accessory.  Unscrew and
remove the feet supplied with the
machine before fitting the longer
screw feet.

The cover plate on the dryer must
be aligned horizontally underneath
the worktop.

,

The ventilation gaps in the plinth

must not be covered over as this
would prevent a sufficient intake of
air.

Room in which the dryer is located

Air taken in for use in the drying
process will be warm when it is
expelled from underneath the dryer.
This expelled air heats up the air in the
room. It is therefore very important to
ensure that the room is adequately
ventilated, particularly if the dryer is
located in a small room. Otherwise
running times and energy consumption
could be increased.

Washer-dryer stack

The tumble dryer can also be
combined with a Miele washing
machine in a washer-dryer stack. To do
this the appropriate stacking kit (WTV)
(available to order from your dealer or
the Miele Spare Parts Department) to
match your dryer is required.

,

The stacking kit must be fitted by

suitably qualified fitter.

Before moving the machine again
(e.g. when moving house)

After each use a small quantity of
condensed water will collect in the area
around the pump. This water can run
out, if the machine is tipped up when it
is being moved. It is a good idea to run
the

Cool air

programme for

approximately 1 minute before moving
the machine. Any remaining condensed
water will then be fed into the
condensed water container or out
through the drain hose.

Installation

39

Summary of Contents for T 4659 Ci





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands