Miele T 240 Operating Instructions Manual Download Page 19

Page: 19 / 52

The system lock prevents anyone
from interfering with the dryer.

If the system lock has been activated it
is not possible to start a programme.

The following

steps

(

...) must

be carried out

in the correct order

To activate the system lock

Ensure that the door is closed and
that the programme selector is
turned to

Finish

Switch the machine on.

Press the

Short

button and keep it

pressed in whilst carrying out steps

Slowly turn the programme selector
clockwise step by step until it
reaches the COTTONS

Normal

posi-

tion.

Slowly turn the programme selector
anti-clockwise step by step to

Finish

Slowly turn the programme selector
anti-clockwise step by step to the
MINIMUM IRON

Hand iron

position.

The

Locked

indicator lamp will flash.

Then release the

Short

button.

The system lock is now activated.

Switch the machine off with the

I-On /

0-Off

button.

To deactivate the system lock

Repeat steps

The

Locked

indicator lamp will go out

after step

Electronic system lock

Summary of Contents for T 240





















































Search results

Summary of Contents for T 240

Reviews:

Related manuals for T 240

Brands by name

Popular brands

Miele T 240, Operating Instructions Manual

Search results

Summary of Contents for T 240

Reviews:

Related manuals for T 240

Brands by name

Popular brands