Miele PW 6065 Plus Operating Manual Download Page 68

Page: 68 / 72

Optimize energy

The energy use for the programs
"Cottons Hygiene", "Cottons Uni."
and "Minimum iron" is at its optimum
when this option is turned on.

The machine comes factory set with
this option "on".

No. rinses Cottons

The programs "Cottons Hygiene"
and "Cottons Uni." allow you to
change the number of rinse cycles.

2 rinses (factory default)
3 rinses
4 rinses
5 rinses

No. rinses min. iron

The program "Minimum iron" allows
you to change the number of rinses.

2 rinses (factory default)
3 rinses
4 rinses

Pre-rinse Cottons

The programs "Cottons Hygiene"
and "Cottons Uni." allows you to add
a pre-rinse of the laundry.

The machine comes factory set with
this option "off".

Pre-rinse Min. iron

The program "Minimum iron" allows a
pre-rinse of the laundry.

The machine comes factory set with
this option "off".

Spin free of charge

When operated by a coin
mechanism, the program "Spin" can
be activated free of charge.

The machine comes factory set with
this option "off".

Menu Settings - Supervisor level

Summary of Contents for PW 6065 Plus









































































Search results

Summary of Contents for PW 6065 Plus

Reviews:

Miele PW 6065 Plus, Operating Manual, Page: 68 / 72

Search results

Summary of Contents for PW 6065 Plus

Reviews: