Miele PT 7136 Plus User Manual Download Page 56

Page: 56 / 60

Contrast/Brightness

Display contrast and brightness can
be adjusted in 10 levels.

The bar shows the selected level.

Standby

The display goes into standby mode
after 10 minutes and the "Start"
button flashes slowly to save energy.

Standby is turned on:

– when no program was selected.

– after pressing the "Start" button.

– at the end of a program.

not during current program
(factory default)

The Standby is turned on:

– when no program is selected.

Pressing any button or turning the jog
shuttle turns the display on again.

Lengthening the cooling time

The cooling phase can be
lengthened before the program is
started. The laundry will be cooled.

The bar shows the selected level.

Delivery status: 0 minutes

(normal

cooling down phase).

– The program duration is extended

respectively.

The cooling time cannot be extended in
the programs "Warm air, Cool air,
Woollen handcare, Smoothing".

Settings

Summary of Contents for PT 7136 Plus




























































Search results

Summary of Contents for PT 7136 Plus

Reviews:

Related manuals for PT 7136 Plus

Brands by name

Popular brands

Miele PT 7136 Plus, User Manual

Search results

Summary of Contents for PT 7136 Plus

Reviews:

Related manuals for PT 7136 Plus

Brands by name

Popular brands