Miele Paragon Plus Operating Instructions Manual Download Page 62

Page: 62 / 68

Keypad tones

An audible tone sounds each time a
button is pressed.

The washing machine is delivered with
the keypad tone switched off.

Follow steps

to programme

and store in memory.

Before you begin, first ensure that:

– The washing machine is switched off.

– The drum door is properly closed.

Press the

Start/Stop

button and keep

it pressed in whilst carrying out steps

Press the

I-On/0-Off

button in.

Wait until the indicator light for the

Start/Stop

button comes on . . .

. . . and then release the

Start/Stop

button.

Press the

Buzzer

button five times.

– The

Buzzer

indicator light will flash

six times.

will flash in the display alternating

with the number

= keypad tone is

deactivated

= keypad tone is

activated

Press the

Start/Stop

button to

change the display from

(activated) or from

(deactivated).

Switch the machine off with the

I-On/0-Off

button.

The setting you have selected is now
stored in memory and will remain so
until you alter it.

Programmable functions

Summary of Contents for Paragon Plus





































































Search results

Summary of Contents for Paragon Plus

Reviews:

Related manuals for Paragon Plus

Brands by name

Popular brands

Miele Paragon Plus, Operating Instructions Manual

Search results

Summary of Contents for Paragon Plus

Reviews:

Related manuals for Paragon Plus

Brands by name

Popular brands