Miele Honeycomb care Paragon sensor Operating Instructions Manual Download | Manualshive

Page: 26 / 56

background image

Cleaning the condenser unit

Detergent residue, hair and fine fluff
from the dryer can get through the fluff
filters and block the condenser unit.
Dust from the room in which the dryer is
installed can also get into the
condenser unit and cause a blockage.

Check

the condenser unit at least

twice a year. Always check it if the

Airways

indicator light comes on. If

the dryer is used frequently then
check the condenser unit after
approx. 100 drying cycles. Clean it if
necessary.

Removing the condenser unit

^

Open the service panel. Hold the
panel securely when doing this.

^

Now remove the panel by pulling it
diagonally upwards and place it to
one side.

^

Turn the lever on the inner cover
downwards to the vertical position.

^

Pull the cover forwards.

^

Remove it by pulling it diagonally
upwards.

^

Turn the lever on the condenser unit
upwards to the vertical position.

Cleaning and care

26

«
...
24
25
26
27
28
...
»

Summary of Contents for Honeycomb care Paragon sensor

























































Reviews:

No comments

Related manuals for Honeycomb care Paragon sensor

Pearl Dryer AC5011

Brand: Remington Pages: 68

Brand: Sierra Pages: 25

Brand: REVLON Pages: 32

Brand: Kitchen Couture Pages: 14

Brand: Princess Pages: 97

Brand: German pool Pages: 17

Brand: Dyson Pages: 24

Brand: N'DUSTRIO Pages: 134

Brand: Roper Pages: 16

AirCrisp Series

Brand: Dash Pages: 20

Ultimate EZ Clean Deep Fryer

Brand: T-Fal Pages: 30

EconoRed Series

Brand: VASTEX Pages: 20

Brand: baridi Pages: 10

Brand: Emerson Pages: 26

Brand: Emerson Pages: 4

Brand: GE Pages: 12

Brand: GE Pages: 16

Brand: GE Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands