background image

Settings menu

98

Check filters

You can adjust the interval at which the
message to remind you to check the
filters appears. 
You can set an interval of between 30
and 60 programme cycles.

The “Check filters” message is set at
the factory to appear after every 50
programme cycles.

Select the interval you want and
confirm this with 

OK

.

Automatic

You can adjust the 

Automatic

programme so that it will remove
stubborn soiling from an otherwise
lightly soiled load. This will increase
energy consumption.

Select the setting you want and
confirm with 

OK

.

AutoOpen

Towards the end of some programmes
the door will open automatically a little
in order to assist the drying process.

This function can be deactivated if
wished.

Select the setting you want and
confirm with 

OK

.

If you have deactivated the

automatic door opening function but
would still like to open the door at
the end of the programme, then
make sure that you open the door
fully. Otherwise steam from the
dishwasher could damage the edge
of the worktop because the fan is no
longer running.

Summary of Contents for G 6727









































































































Reviews: