Miele G 603 Installation Instructions Manual Download Page 16 | Manualshive

Page: 16 / 28

background image

4. Adjusting the door front

When fitted the door front can be ad-
justed up to a maximum of 2 mm up-
wards or downwards to match adjoining
unit fronts.

^

Open the dishwasher door slightly.

^

With the door open, press the front
panel on one side against the door
outer panel.

^

Adjust the height of the door front on
this side using the lower recessed
adjusting screw (TORX T20).

higher = turn clockwise
lower = turn anti-clockwise

^

Then secure the door front on this
side by tightening the upper re-
cessed fixing screw (TORX T20) at
the side of the machine door outer
panel.

^

Repeat the process on the other side
of the door.

^

Close the dishwasher door.

^

Check the alignment of the door
panel again.

^

If it is not correctly aligned you may
need to loosen the screws and re-ad-
just it to the correct alignment.

Once satisfied that the alignment is cor-
rect:

^

Open the dishwasher door.

^

Tighten all fixing screws (upper
screws, TORX T20) at the sides.

^

Plug fixing screw and height adjust-
ment screw recesses with the plastic
stoppers supplied.

Installation

16

«
...
14
15
16
17
18
...
»

Summary of Contents for G 603





























Reviews:

No comments

Related manuals for G 603

Brand: Daewoo Pages: 33

Brand: Amica Pages: 52

Brand: V-ZUG Pages: 56

Brand: ZANKER Pages: 40

Brand: ZANKER Pages: 48

Brand: Gaggenau Pages: 64

Brand: BENDIX Pages: 24

Brand: Belling Pages: 24

Brand: BENDIX Pages: 24

Brand: Hotpoint Pages: 24

Brand: Ariston Pages: 60

Brand: Thermador Pages: 66

Brand: Asko Pages: 24

Brand: Brandt Pages: 42

Brand: Hanseatic Pages: 84

Brand: Lamona Pages: 40

Brand: Samsung Pages: 22

Brand: Samsung Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands