Miele G 5481 Operating Instructions Manual Download Page 6 | Manualshive

Page: 6 / 92

background image

Warning and Safety instructions

6

This dishwasher complies with all current local and national safety
requirements. However, inappropriate use can lead to personal
injury and damage to property.

Please observe the installation sheet and read the operating
instructions carefully before setting up the dishwasher and using it
for the first time. They both contain important information on the
installation, safety, use, and maintenance of the machine. This
prevents both personal injury and damage to the dishwasher.

In accordance with standard IEC 60335-1, Miele expressly and
strongly advises that you read and follow the instructions in
"Installation" and in "Warning and Safety instructions".
Miele cannot be held liable for injury or damage caused by non-
compliance with these instructions.

Keep the installation sheet and the operating instructions in a safe
place and pass them on to any future owner.

«
...
4
5
6
7
8
...
»

Summary of Contents for G 5481





























































































Reviews:

No comments

Related manuals for G 5481

Brand: lamber Pages: 70

Brand: Lamona Pages: 12

Brand: Infiniton Pages: 127

Brand: Fagor Pages: 108

Brand: THOMSON Pages: 36

Evo Concept Series

Brand: Fagor Pages: 66

T-1200 WC1200XA-12

Brand: Dexter Laundry Pages: 25

Brand: Heinner Pages: 50

Brand: Classeq Pages: 48

Brand: Fagor Pages: 115

Brand: GE Pages: 20

Brand: GE Pages: 16

Brand: GE Pages: 41

Brand: GE Pages: 2

Brand: Samsung Pages: 44

Brand: Samsung Pages: 24

Brand: Samsung Pages: 96

WA25B8377 Series

Brand: Samsung Pages: 168

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands