Miele FN 28262 Installation Manual Download Page 9

Page: 9 / 12

11210610-01

Installation

*INSTALLATION*

Changing over the lower hinge plate



Pull the hinge pin



complete with

washer



and adjusting foot



upwards to remove.



Remove the stopper





Undo the screws



and remove the

hinge plate





Slightly loosen the screw of the door
closing aid



on the hinge plate



Place the door closing aid



in the

opposite mounting hole in the hinge
plate and then tighten the screw.



Insert the stopper



into the other

hole.



Remove the cover





Remove the screw



and screw it

into the outside hole on the opposite
side.



Turn the cover



180° and refit it in

the holes on the opposite side.



Screw the hinge plate



securely into

position on the new hinge side with
the screws





Reinsert the hinge pin



complete

with washer



and adjustable

foot



. Important: The lug on the

hinge pin must point to the back
again.



Place the door onto the hinge pin



from above.



Close the appliance door.

Summary of Contents for FN 28262













Search results

Summary of Contents for FN 28262

Reviews:

Related manuals for FN 28262

Brands by name

Popular brands

Miele FN 28262, Installation Manual

Search results

Summary of Contents for FN 28262

Reviews:

Related manuals for FN 28262

Brands by name

Popular brands