Miele F1411VI Page 71 Operating And Installation Instructions Download

Page: 71 / 76

The Miele RemoteVision system is
designed to send messages directly to
Miele and/or your PC.

For information on set-up and
installation of the RemoteVision module
see the "Installation" section of this
manual.

The RemoteVision system is
available as an optional accessory
from Miele. It can only be installed
by a Miele Service Technician.

Be sure your wireless system meets the
following requirements

– a router that supports an 802.11

wireless standard*

– Windows XP or newer operating

system

– Cable or DSL modem

* Please note that each wireless router
manufacturer supplies their own device
drivers and setup programs. Due to the
differences in manufacturers, exact
router setup instructions are not
included in this manual. Wording and
instructions may vary.

RemoteVision

Summary of Contents for F1411VI













































































Search results

Summary of Contents for F1411VI

Reviews:

Related manuals for F1411VI

Brands by name

Popular brands

Miele F1411VI, Operating And Installation Instructions

Search results

Summary of Contents for F1411VI

Reviews:

Related manuals for F1411VI

Brands by name

Popular brands