manualshive.com logo in svg

Miele DA 4208V D, Operating And Installation Instructions

Share
Download
Miele DA 4208V D Operating And Installation Instructions Download Page 22

Before using for the first time

22

Con@ctivity via the home WiFi
network (Con@ctivity 3.0)

Prerequisite:

– Home WiFi network

– WiFi-enabled Miele hob

Connect the cooker hood and hob to
your home WiFi network (see “Setting
up Miele@home”).

The Con@ctivity function will be
activated automatically.

Con@ctivity via a direct WiFi
connection (Con@ctivity 3.0)

Prerequisite:

– WiFi enabled Miele hob

If you do not have a home network, you
can establish a direct connection
between the hob and the cooker hood.

See the Hob instruction manual for
details on how to connect them.

Instructions on how to connect the
cooker hood are repeated in detail
below.

Switch the cooker hood off.

Press and hold the 

 control.

Press the 

 control at the same time.

2

 will light up constantly, 

3

 will flash on

and off.

The cooker hood will be ready for
connection in the next 2 minutes.

Summary of Contents for DA 4208V D

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands