Miele CM6x10 Operating Instructions Manual Download Page 53

Page: 53 / 84

Cleaning and care

Drip tray and waste container

Clean the drip tray and waste
container

every day

to avoid

unpleasant smells and mildew.

The waste container is located in the
drip tray. Water from rinsing also
collects in the waste container.

A prompt will appear in the display
when the drip tray and/or the waste
container is full and needs to be
emptied. Empty the drip tray

and

the

waste container.

Danger of burning.
If the rinsing process has just
finished, wait a while before
removing the drip tray as the water
used for rinsing will run out of the
coffee spouts.



Push the central spout up as far as it
will go.



Pull the drip tray carefully out of the
machine. Take the lid off





Empty the drip tray

and

the waste

container.



Remove drip tray cover



and lower

panel





Clean all parts thoroughly.

Clean the lower panel by hand only
using hot water and a little washing-
up liquid.
All other parts are dishwasher safe.



Clean the inside of the machine
underneath the drip tray.



Reassemble all parts and place the
drip tray back in the coffee machine.

Make sure the drip tray has been
pushed right into the machine as far
as it will go.

Summary of Contents for CM6x10





















































































Search results

Summary of Contents for CM6x10

Reviews:

Related manuals for CM6x10

Brands by name

Popular brands

Miele CM6x10, Operating Instructions Manual

Search results

Summary of Contents for CM6x10

Reviews:

Related manuals for CM6x10

Brands by name

Popular brands