manualshive.com logo in svg

Miele B 990, Operating Instructions Manual

Share
Download
Miele B 990 Operating Instructions Manual Download Page 24

Collar

Iron the collar from both sides. Do not
iron any buttons!

^

Turn the collar and press if wished.

Nightdresses

Iron sleeves, yokes and back on a
nightdress as you would a shirt.

To iron the front:

^

Pull the nightdress over the roller
leaving the sleeves and bodice
hanging over the left hand side of the
roller.

^

Iron starting from the left hand side
seam and finishing at the right hand
side seam. Then adjust the bodice
section on the roller to iron it.

^

If there is a collar follow the
instructions for ironing shirts.

Pyjamas

Pyjamas tops should be ironed
following instructions for shirts. Iron
trouser legs on pyjamas separately.

^

Iron one leg from the front and the
other from the back.

^

Iron from the top to the bottom.

^

Then pull into shape and iron to the
waist. Pull the elasticated section
tight.

Aprons

^

Iron any straps as far as the apron
first.

^

Then iron either to the waistband or
across the apron. Leave the bib
hanging over the left hand side of the
roller.

Ironing tips

24

Summary of Contents for B 990





































Reviews:

No comments

Brands by name

Popular brands

Load more brands