Miele B 2312 Operating Instructions Manual Download Page 23

Page: 23 / 76

Setting the water hardness
level

You can programme the water
hardness level using the buttons on the
control panel.

The programming procedure can be
cancelled at any time by pressing
the

button. The procedure can

then be restarted from the beginning
again.

To programme the water hardness
level:

Switch off the steam ironing system
using the

button if it is switched

on.

Press and hold the

button and

simultaneously

switch on the

appliance with the

button. Hold

the

button until the indicator light

lights up yellow.

If this does not happen, start the
procedure from the beginning again.

The indicator light

flashes 10 times at

intervals and the indicator light

gives

one long flash (default setting).

The programmed water hardness level
can be recognised by the flash
frequency of the indicator light

(see

chart for water hardness).

Press the

button briefly to select

the number of flashes which equates
to your water hardness level.
Each press of the button moves you
up a level. When the highest water
hardness level is reached, the setting
starts from the beginning again.

To avoid your warranty becoming
invalidated, ensure the water hardness
level is correctly programmed.

Example:

Your water hardness level is 22°dH
(AU/NZ 4.0 mmol/l).

– The indicator light

flashes 10 times

at intervals (default setting).

– Press the

button six times.

– The indicator light

flashes six times

at intervals.

Press the

button to switch the

steam ironing system off.

Checking the programmed
water hardness level

Switch off the steam ironing system
using the

button if it is switched

on.

Press and hold the

button and

simultaneously

switch on the

appliance with the

button. Hold

the

button until the indicator light

lights up yellow.

The indicator light

will flash for the

number of times which corresponds to
the water hardness level which has
been set (see chart).

Press the

button to switch the

steam ironing system off.

Before using for the first time

Summary of Contents for B 2312













































































Search results

Summary of Contents for B 2312

Reviews:

Miele B 2312, Operating Instructions Manual, Page: 23 / 76

Search results

Summary of Contents for B 2312

Reviews: