Miele 11070970 Operating Instructions Manual Download Page 80

Page: 80 / 120

Problem solving guide

Water inlet fault

Problem

Cause and remedy

The optical in-operation
indicator light is flash-
ing quickly.
The alarm tone is
sounding.
One of the following
messages appears in
the display:



Open stopcock

The stopcock is closed.



Open the stopcock fully.



Water intake

Before rectifying the problem:



Switch the dishwasher off.

The water inlet is restricted.



Open the stopcock fully and start the programme
again.



Clean the filter in the water inlet (see “Cleaning
and care” chapter, “Cleaning the filter in the water
inlet” section).



The water-connection pressure is lower than
50 kPa.
Seek professional advice.



The on-site connection for the water drainage may
be too low and you will need to vent the water
drainage (see “Installation” chapter, “Water drain-
age” section).

The following fault mes-
sage appears during the

SolarSave

programme:

Intake temperture too low

The inlet water has not reached the required temper-
ature of 45 °C (see “Installation” chapter, “Water inlet”
section).



Start the programme again.



If the fault message appears again, select a differ-
ent programme.

Summary of Contents for 11070970

























































































































Search results

Summary of Contents for 11070970

Reviews:

Related manuals for 11070970

Brands by name

Popular brands

Miele 11070970, Operating Instructions Manual

Search results

Summary of Contents for 11070970

Reviews:

Related manuals for 11070970

Brands by name

Popular brands