background image

 

Technical Service Guide 

Compact Dishwasher 

6 settings

 

MODEL SERIES: 

WQP6-3305E

 

 
 

IMPORTANT SAFETY NOTICE 

The information in this service guide is intended for use by individuals possessing adequate backgrounds of 
electrical, electronic, and mechanical experience. Any attempt to repair a major appliance may result in personal 
injury and property damage. The manufacturer or seller cannot be responsible for the interpretation of this 
information, nor can it assume any liability in connection with its use.   

 
 

WARNING  

To avoid personal injury, disconnect power before servicing this product. If electrical power is required for diagnosis 
or test purposes, disconnect the power immediately after performing the necessary checks.   

 
 

RECONNECT ALL GROUNDING DEVICES   

If grounding wires, screws, straps, clips, nuts, or washers used to complete a path to ground are removed for 
service, they must be returned to their original position and properly fastened. 
 
 
 
 
 

 

MIDEA

 

C

ONSUMER 

P

RODUCTS

 

 

T

ECHNICAL 

S

ERVICE 

G

UIDE 

 

COPYRIGHT.

 

2003

 

 

A

LL RIGHTS RESERVED

.

 

T

HIS SERVICE GUIDE MAY NOT BE REPRODUCED IN WHOLE OR IN PART

,

 IN ANY FORM

,

 WITHOUT 

WRITTEN PERMISSION FROM THE MIDEA DISHWASHER MANUFACTURING 

C

OMPANY

.

 

 

CONTENTS 

Introduction

 

.............................................................................................................................................................

 

3

 

Specification

 

...........................................................................................................................................................

 

3

 

Control Panel Features

 

.........................................................................................................................................

 

3

 

Component Locator Views

 

...................................................................................................................................

 

3

 

Dishwasher Components

 

.....................................................................................................................................

 

5

 

Main control board

 

.........................................................................................................................................

 

5

 

Outer Door

 

......................................................................................................................................................

 

6

 

Dispenser

 

........................................................................................................................................................

 

7

 

Door Handle Assembly

 

.................................................................................................................................

 

8

 

Microswitch (door handle assembly)

 

..........................................................................................................

 

9

 

Inner Door

 

.......................................................................................................................................................

 

9

 

Shell

 

.................................................................................................................................................................

 

9

 

Operating board

 

...........................................................................................................................................

 

10

 

Air Breather Assembly

 

................................................................................................................................

 

11

 

Siphon

 

...........................................................................................................................................................

 

11

 

Pressure switch

 

............................................................................................................................................

 

12

 

Tank assembly

 

.............................................................................................................................................

 

12

 

Summary of Contents for WQP6-3305E series
























Reviews: