manualshive.com logo in svg

Midea TC051K6BW-S, Instruction Manual, Page: 35 / 50

Share
Download
Midea TC051K6BW-S Instruction Manual Download Page 35

Wall

Mounting

Plate

Spacing for Toggles

More Than Wall

Thickness

Bolt End

Toggle 

Bolt

Toggle Wings

35

To use toggle bolts:

C2. USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET

You need to drill holes for the top support screws, a hole large enough for the power cord 

to fit through, and a cutout large enough for the exhaust adaptor.

• Read the instructions on the TOP CABINET TEMPLATE.

• Tape it underneath the top cabinet.

• Drill the holes, following the instructions o

n the TOP CABINET TEMPLATE.

CAUTION: Wear safety goggles when drilling holes in the cabinet bottom.

Place the mounting plate against the wall and insert the toggle wings into the holes in the 

wall to mount the plate.
NOTE: Before tightening toggle bolts and wood screw, make sure the bottom of the 

mounting plate touch the bottom of the cabinet when pushed flush against the wall and 

that the plate is properly centered under the cabinet.
CAUTION: Be careful to avoid pinching fingers between the back of the mounting plate 

and the wall.
4. Tighten all bolts. Pull the plate away from the wall to help tighten the bolts.

C. ADAPTING MICROWAVE BLOWER FOR OUTSIDE TOP EXHAUST
1. Place the microwave in its upright position, with the top of the unit facing up.

Summary of Contents for TC051K6BW-S



















































Reviews:

No comments