background image

1.SAFETY PRECAUTION

P.04

1.Do not try to repair the machine by yourself. The machine may be damaged and its life 

 

be shortened.

    What is worse, it will injure yourself.
2.Pull out its plug from the power socket before maintenance. Electricity!
3.Do not use several power plug with one socket.
   To avoid fire, don’t use any socket with its actual current more than rated current.
4.Please check the power plug and socket whether damaged or not.
   To avoid an electrical shock and fire, the power plug and socket should be replaced if 

 

they are damaged.

.Don’t try to clean up the washing machine with water, or else, it’s possible to cause an 

  

electrical shock or

   

and shorten its life.

 fire 

6.Forbid the harness contact with water for avoiding wet and don’t extend it during 

 

maintenance. Don’t twist

    the harness to avoid it distorted.
7.Please clean up the dirt and dust on the surface of the cabinet, harness and connection parts during 

   Please avoid fire because of the electric leakage of harness.
8.Check electrical parts, harness whether they have become moist and replace them if they are wet. 
9.Check all parts of the machine and make sure to keep them in good condition after 

  

maintenance.

10.Fasten upon the power plug and pullit out .
    Be careful of a fire and electric shock when power cord is damaged.
11.Pull out its power plug when this machine doesn’t work.
    Be careful of an electric shock and fire because of levin.
12.Don’t put tinder or sprayer  beside the washing machine.
    Be careful of a fire and explosion because of electric spark.
13.Don’t put a basin of water or  wet clothes on the washing machine.
    It is possible to cause an electric shock or fire if water from wet clothes leaks in to the washing machine.
14.Do not place the washing machine in the place where it can be exposed to rain and 

 

snow. Or else, it may 

     cause an electric shock or fire, and therefore shorten its life.
15.Don’t press the button with sharp items such as nail, screw etc. Or else, it may cause 

 

an electric shock  or

     other damages.
16.This machine should be placed on the horizontal ground and installed correctly. The machine is liable to 
    shift on the gradient ground.
17.If the harness is damaged, it should be replaced completely.
18.It is necessary to put a mat on the floor and recline down the washing machine along 

 

its side when repair it.

    It is possible to damage the electrical components if the front of the washing machine 

 

is placed at the ground.

19.During changing the heater of this machine, please check whether it is fixed on the 

 

blanket correctly and 

    whether the screw is fastened tight or not. 

5

 

maintenance. 

Summary of Contents for A1 4.5kg


































Reviews: