Midea 361170 Installation Instructions & User Manual Download Page 5

6

7

Step 1:Dryer should be placed in a ventilated area with

not less than 10cm distance from the wall. If placed in a

room such as bathe room, it is suggested there are no 

obstacles within 1.5m in front of dryer and keep ventilated.

Step 2:The horizontal adjustment:

Tie a heavy subject on the string on the front and two sides of the dryer.

Please refer this to below figure, and if A=A, B=B, this means the dryer

is placed horizontally. While the opposite, you could place something on

the grounding. 

Notice:

if dryer could not be placed horizontally (the 

lean angle is no more than 2), the dryer will

work unbalanced or stop working sometimes. 

Notice when installing:

• Do not install the dryer in the open air or place easily damaged by rain;

• Do not place the back of dryer near curtain or something in the wind;

• Do not place the dryer near gas or flammable area.

Simple installation

>10cm

The heavy

A

A’

B

B’

Simple installation

Do not store plastic, paper or clothing that may

burn or melt on top of the dryer during operation.

Do not dry articles containing rubber, plastic or similar

materials such as padded bras, tennis shoes, 

galoshes, bath mats, rugs, bibs, baby pants, raincoat 

plastic bags or pillows that may melt or burn. Some 

rubber materials, when heated, can under certain 

circumstances produce fire by spontaneous 

combustion.  

The door can be opened only after the 

programme of the drying machine is completed.

Do not open the door before the programme 

finished to avoid the human skin from being 

scalded by hot steam or over heated drying

machine. 

This product belongs to type I electronic products and please take note of safety problem accordingly:
1.It is rule to use power which is buried in the earth and will not touch any socialequipments such as
gas pipe or water pipe etc. Make sure the difference of different lines and they are not connected.
2.Please use special socket which is according to National Standard and will endure 10A current.

To be safe, please make improvements as soon as possible according to the rules and suggestions
mentioned above.

  Please pay attention to use the drying machine if the materials of your clothes can not be dried by it or 

contain the symbols as follows:

Dry

Dry clean 

Line dry / hang to dry  

 Drip dry 

 Do not dry clean

 Normal

 Do not dry 

In the shade 

 Dry flat

 Not tumble dry normal

 Dry clean normal cycle

with any solvent

 Dry clean normal cycle

petroleum solvent only

Installation before use 

Summary of Contents for 361170











Reviews: