background image

CAUTION 

- Personal Injury Hazard

Tightly-closed 

s could explode. Closed containers should be opened and plastic 

pouches should be pierced before cooking.

See the instructions on "Materials you can use in microwave oven or to be avoided in 

microwave oven."

There may be certain non-metallic utensils that are not safe to use for microwaving. If in 

doubt, you can test the utensil in question following the procedure below.

Utensil Test:

Fill a microwave-safe container with 1 cup of cold water (250ml) along with the utensil 

in question.

Cook on maximum power for 1 minute.

Carefully feel the utensil. If the empty utensil is warm, do not use it for microwave 

cooking.

Do not exceed 1 minute cooking time

.

1.

2.

3.

4.

UTENSILS

7

container

 for the test

Use care when cooking food in the microwave oven to avoid burning due to 

excessive cooking.

Failure to maintain the oven in a clean condition could lead to deterioration that 

could adversely affect the life of the appliance and possibly result in a hazardous 

situation.

12.

1 .

To prevent delayed eruptive boiling of hot liquids and beverages or scalding yourself, 

stir liquid before placing the container in the oven and again halfway through cooking 

time. Let stand in the oven for a short time and stir again before removing the 

container.

11.

3

Summary of Contents for 1134G1A

























Reviews: