manualshive.com logo in svg

Middleby Crown EPXN-3, Installation & Operation Manual

Share
Download
Middleby Crown EPXN-3 Installation & Operation Manual Download Page 19

INSTALLATION & OPERATION MANUAL, ELECTRIC COUNTER PAN STEAMERS, EPXN-3, EPXN-5

8.0  TROUBLESHOOTING

GENERAL

PROBLEM

PROBABLE CAUSE

REMEDY

1. C

OOKING INDICATOR

LIGHT FAILS TO LIGHT

WITH 

T

IMER  SET

.

a. Main power circuit breaker

tripped.

Locate external circuit breaker for incoming
power and place in ON position.

b. Door interlock switch contacts not

closed.

Shut cooker door to close switch contacts.  
Check alignment of door with switch.

c.  Door interlock switch faulty.

Replace switch.

d.  Indicator light burned out.

Replace light.

e. Faulty timer contacts.

Replace timer.

f.  Faulty wiring.

Inspect condition of wire and tightness of all
connections.  Correct as needed.

g.  Fuse blown.

Replace with same rated fuse.

2.

  

S

TEAM FAILS TO 

GENERATE WITH COOKING

INDICATOR LIGHT ON

.

a.  Faulty wiring.

Inspect condition of wire and tightness of all
connections.  Correct as needed.

3. S

TEAMS  CONTINUOUSLY

WITHOUT THE COOKING

OR READY LIGHT ON 

.

a.  Faulty thermostatic switch.

Replace thermostat.

b.  Power switch - continuous steam  
      setting is selected.

This is normal operation when “continuous
steam” is selected.

4. T

IMER DIAL NOT TURNING

.

a.  Faulty timer motor.

Replace timer.

b.  Faulty wiring.

Inspect condition of wire and tightness of all
connections.  Correct as needed.

5.

BUZZER FAILS TO SOUND

AT END OF TIMER

SETTING

.

a.  Timer contacts faulty.

Replace timer.

b.  Buzzer faulty.

Replace buzzer.

c.  Faulty wiring.

Inspect condition of wire and tightness of all
connections.  Correct as needed.

Part No. 10234R3

19

2020-02-24

Summary of Contents for Crown EPXN-3

























Reviews:

No comments

Brands by name

Popular brands

Load more brands