Midcontinent MD93 Series Installation Manual And Operating Instructions Download Page 19

 

Mid-Continent Instruments and Avionics 
Revision D, March 21, 2016 

 

Manual Number 9018205 

19 

 

SECTION 6  CONFORMANCE 

6.1 

INSTRUCTIONS FOR CONTINUED AIRWORTHINESS

 

No periodic scheduled maintenance or calibration is necessary for continued airworthiness of the MD93 
Digital Clock / Dual USB Charging Port. If the unit fails to perform to specifications, the unit must be 
removed and serviced by Mid-Continent Instruments and Avionics or their authorized designee. 
 

6.2 ENVIRONMENTAL 

QUALIFICATION 

STATEMENT 

MODEL NUMBER:

   

MD93 Series 

 

PART NUMBER:

  

6420093-()                          

NOMENCLATURE:

  

Digital Clock/USB Charging Port 

 

 
MANUFACTURER:

          Mid-Continent Instrument Co., Inc. 

ADDRESS:

                       9400 E. 34

th

 St. North, Wichita, KS  67226, USA. 

MANUFACTURERS SPECIFICATIONS: 

 

Minimum Performance Specifications: 

TS509 6430102-(), TDS509 6430102-(), TDS093 6420093-( ) 

 

Qualification Test Reports:   

QTR1901-1902, QTR1904-1908-1 & 1908-2, QTR1915-1917 

 
RTCA DO-160

:   

Rev G, dtd 12/08/10   

 

DATES TESTED:

   

7/2014-9/2014 

 

 

CONDITIONS 

SECTION

DESCRIPTION OF TEST

Temperature and Altitude 
 Low 

Temperature 

 High 

Temperature 

 Altitude 
   

4.5.1 
4.5.2 
4.6.1 

 

Category F1 

Short and Normal Operating Low Temp = -40C 

Short Time Operating High Temp = +70C 

Normal Operating High Temp = +55C 

Altitude = 55,000 ft 

Temperature Variation 

Category S2 

Humidity 6 

Category 

Operational Shock and 
Crash Safety 

7 Category 

Vibration 

Category R; Curves C, C1  

Category U, Curve G 

Explosion 9 

Category 

Waterproofness 10 

Category 

Fluids 11 

Category 

Sand and Dust 

12 

Category X 

Fungus 13 

Category 

Salt Spray 

14 

Category X 

Magnetic Effect 

15 

Category Y 

Power Input 

16 

Category B(XX) 

Voltage Spike 

17 

Category B 

Audio Frequency Conducted Susceptibility 

18 

Category R 

Induced Signal Susceptibility 

19 

Category X 

Radio Frequency Susceptibility 

20 

Category X  

Emission of Radio Freq Energy 

21 

Category M 

Lightning Induced Transient Susceptibility 

22 

Category X 

Lightning Direct Effects 23 Category 

Icing 24 

Category 

ESD 25 

Category 

Fire, Flammability 

26 

Category X 

REMARKS: 

Section 4: Category F1 Operating Low temperature performed at Short-time Low temperature set point of -40C. 
Section 8:  Vibration was performed per Cat R, Curves C & C1 for fixed-wing aircraft and per Cat U, Curve G for 
helicopter using the same test article. 

 

Summary of Contents for MD93 Series




















Reviews: