Microsemi SyncServer S600 User Manual Download Page 95

Page: 95 / 252

098-00720-000 Revision B – April, 2016

SyncServer 600 Series User’s Guide

Chapter 4

Navigation Windows

Figure 4-33. Security - NTPd Autokey Server Configuration Window

Security - NTPd Autokey Client Configuration Window

Use this window to configure the NTP Autokey Client and install the IFF Group Key
file. See

Figure 4-34

Figure 4-34. Security - NTPd Autokey Client Configuration Window

Security - RADIUS Configuration Window

Use this window to enable and configure RADIUS authentication. Up to 5 RADIUS
servers can be configured. See

Figure 4-35

Note:



RADIUS key: 1-16 characters

Summary of Contents for SyncServer S600





























































































































































































































































Search results

Summary of Contents for SyncServer S600

Reviews:

Related manuals for SyncServer S600

Brands by name

Popular brands

Microsemi SyncServer S600, User Manual

Search results

Summary of Contents for SyncServer S600

Reviews:

Related manuals for SyncServer S600

Brands by name

Popular brands