manualshive.com logo in svg

Microsemi SyncServer S600, User Manual

Share
Download
Microsemi SyncServer S600 User Manual Download Page 35

098-00720-000 Revision B – April, 2016

SyncServer 600 Series User’s Guide

35

Chapter 1  Overview

Configuration Management

Web Interface

The SyncServer S6x0 also allows the user to access information via the LAN1 
Ethernet port using HTTPS protocol. To use the SyncServer S6x0 web interface, 
enter the IP address for Ethernet port 1 into a web browser. Enter your user name 
and password for the SyncServer S6x0 when prompted. 

Dashboard View

See 

Figure 1-19

 for an example of the dashboard status screen that will appear. 

Figure 1-19.  Web Interface - Dashboard 

Command Line Interface (CLI)

The Command Line Interface can be used to control specific function of the 
SyncServer S6x0 from a terminal connected to the EIA-232 serial port or the 
Ethernet LAN1 port. Refer to 

Chapter 5, Command Line Interface (CLI)

 for further 

details.

Note:

 Before you can communicate with the SyncServer S6x0 

through an Ethernet connection, you must first configure the Ethernet 
port using the serial connection or front panel (see 

Provisioning the 

Ethernet Ports

, on page 142).

Summary of Contents for SyncServer S600





























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands