Microsemi SyncServer S600 User Manual Download Page 206

Page: 206 / 252

206

SyncServer 600 Series User’s Guide

098-00720-000 Revision B – April, 2016

Appendix B Specifications and Factory Defaults
GNSS Antenna Kits Specifications

GNSS Antenna Kits Specifications

The basic antenna kit (

093-15202-001

) consists of the following



GNSS Antenna (112-00079-000) with internal LNA



Mounting Bracket (193-00044-000)



Adapter cable for chassis (060-15202-004). This cable has an N-connector on
one end and a BNC-connector on the other end.

Other components available in kits or separately include the following:



Lightning arrestor

(112-43400-00-3)



Inline Amplifier

(112-15202-001)



GPS L1 4:1 Active Splitter (58536A)

See

Table 7-7

for antenna kit part numbers.

Table B-16. Holdover Performance

Oscillator

Holdover - 24 Hour

(



sec)

Standard

400

OCXO

Rubidium

Note:

Holdover values are approximate and assume operation at

constant temperature, no initial frequency or phase offset, and that
the unit has been powered on for 2 weeks and locked to GNSS for
three consecutive days.

Summary of Contents for SyncServer S600





























































































































































































































































Search results

Summary of Contents for SyncServer S600

Reviews:

Related manuals for SyncServer S600

Brands by name

Popular brands

Microsemi SyncServer S600, User Manual

Search results

Summary of Contents for SyncServer S600

Reviews:

Related manuals for SyncServer S600

Brands by name

Popular brands