manualshive.com logo in svg

Microsemi SmartFusion2 MSS, User Manual

Download the free Configuration Manual for Microsemi SmartFusion2 MSS, a cutting-edge product designed for seamless integration and optimized performance. Unlock the full potential of this advanced solution by accessing the comprehensive manual, available for download at our website. Get started now and elevate your technological possibilities with ease.

Share
Download
background image

Reset Controller

UG0331 User Guide Revision 15.0

660

Figure 294 • 

MSS GPIO_OUT Reset Generation

21.2.6.6 Reset Generation to MSS Peripherals

The Reset Controller generates block level resets for the peripherals present within the MSS. The block 
level reset generation is shown in the following figure.

Figure 295 • 

Block Level Reset Generation

The reset signal is asserted if any of the following conditions is true:

•

SYSRESET_N asserted

•

Block level Soft reset (SOFT_RESET_CR) request asserted from SYSREG module.

The Reset Controller can generate the reset to ENVM_0, ENVM_1(if present), ESRAM_0, ESRAM_1, 
Ethernet MAC, PDMA, MMUART_0, MMUART_1, SPI_0, SPI_1, I2C_0, I2C_1, TIMER, CAN (if 
present), HPDMA, USB OTG, COMM_BLK, FIC_0, FIC_1 (if present), MSS_GPIO 
(MSS_GPIO_RESET_N reset), and the FPGA fabric (MSS_RESET_N_M2F reset).

21.3

CoreResetP Soft Reset Controller

The following Reset sub-systems in SmartFusion2 devices that must be sequenced properly for the 
overall system to function correctly.

•

Chip Boot (System Controller)

•

Fabric

•

MSS, Cortex-M3 processor

•

FIC sub-systems (MSS to Fabric and Fabric to MSS)

•

Peripherals - MDDR, FDDR and SERDESIF

CoreResetP Soft Reset Controller gathers various reset signals from system controller, MSS and FPGA 
fabric and generates new synchronized reset signals to handles the sequencing of reset signals of 
various subsystems in SmartFusion2 devices. CoreResetP helps manage the following:

Flash Configuration

Bits

SYSREG

FPGA Fabric

MSS_GPIO_31_24_DEF

MSS_GPIO_23_16_DEF

MSS_GPIO_15_8_DEF

MSS_GPIO_7_0_DEF

MSS_GPIO_SOFTRESET

MSS_GPIO_31_24_SOFTRESET

MSS_GPIO_7_0_SOFT_RESET

MSS_GPIO_7_0_SYSRESET_SEL

GPIO_RESET_N

MSS_GPIO_31_24_SYSRESET_SEL

MSS_GPIO_23_16_SOFTRESET

MSS_GPIO_23_16_SYSRESET_SEL

MSS_GPIO_15_8_SOFTRESET

MSS_GPIO_15_8_SYSRESET_SEL

0

1

R

Q

D

S

M3_CLK

MSS_GPIO[31:0]

IOMUX

PORESET_N

APB Interface

Reset

Control

D1

MSS GPIO

R

BLOCK_RESET_N

SYSRESET_N

BLOCK_SOFTRESET

Summary of Contents for SmartFusion2 MSS






























































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartFusion2 MSS

ABB FSCA-01 Manual preview
FSCA-01
Brand: ABB Pages: 52
ABB REC650 ANSI Applications Manual preview
REC650 ANSI
Brand: ABB Pages: 370
ABB EAN823 Instructions Manual preview
EAN823
Brand: ABB Pages: 17
ABB COM600 series User Manual preview
COM600 series
Brand: ABB Pages: 104
ABB AC 800M Library Object Style Manual preview
AC 800M
Brand: ABB Pages: 120
ABB ABILITY SSC600 Product Manual preview
ABILITY SSC600
Brand: ABB Pages: 42
B&R Industries AP1000 User Manual preview
AP1000
Brand: B&R Industries Pages: 89
Vanderbilt SPCN310 Installation Instruction preview
SPCN310
Brand: Vanderbilt Pages: 2
Bardiani Valvole BBZO BBZOG Instruction Manual preview
BBZO BBZOG
Brand: Bardiani Valvole Pages: 24
Viva VRM2 Instruction Manual preview
VRM2
Brand: Viva Pages: 9
Zencontrol zc-iot-fc Quick Start Manual preview
zc-iot-fc
Brand: Zencontrol Pages: 2
Gasboy CFN Series Startup Manual preview
CFN Series
Brand: Gasboy Pages: 119
Dantherm HRC 2 User Manual preview
HRC 2
Brand: Dantherm Pages: 28
Water Specialist WS1TT Drawings And Service Manual preview
WS1TT
Brand: Water Specialist Pages: 36
AC Tech SCF SERIES Quick Reference Manual preview
SCF SERIES
Brand: AC Tech Pages: 2
V-TAC VT-2472 Manual preview
VT-2472
Brand: V-TAC Pages: 2
Diamond Systems Pyxis-MM User Manual preview
Pyxis-MM
Brand: Diamond Systems Pages: 15
Tate Premier SX User Manual preview
Premier SX
Brand: Tate Pages: 32

Brands by name

Popular brands

Load more brands