manualshive.com logo in svg

Microsemi SmartFusion2 MSS, User Manual

Download the free Configuration Manual for Microsemi SmartFusion2 MSS, a cutting-edge product designed for seamless integration and optimized performance. Unlock the full potential of this advanced solution by accessing the comprehensive manual, available for download at our website. Get started now and elevate your technological possibilities with ease.

Share
Download
background image

Cortex-M3 Processor Overview and Debug Features

UG0331 User Guide Revision 15.0

16

2.7

How to Use the Cortex-M3 Processor and the Debug 
Subsystem

2.7.1

Configuration Through Libero Software and Firmware

The Cortex-M3 processor and debug subsystem can be configured using the Libero

®

 SoC design 

software. Using the MSS Cortex-M3 (CM3) configurator macro, various options can be selected, as 
shown in the following figure.

Figure 3 • 

CM3 Configurator

The timing arcs for interrupts to the Cortex-M3 sourced from the FPGA fabric have been updated in 
Libero SoC. In addition, timing arcs for the Cortex-M3 Embedded Trace Macrocell (ETM) have been 
added.

DEEPSLEEP

Out

No

Signal is asserted when the Cortex-M3 processor is in sleep now or sleep-
on-exit mode when the SLEEPDEEP bit of the system control register is 
set.

SLEEPHOLDREQn In

No

Request to extend Cortex-M3 processor sleep state. Signal is asserted 
when SLEEPING signal is High.

SLEEPHOLDACKn

Out

No

Signal is asserted to confirm the Cortex-M3 processor sleep state 
extension request.

TRACECLK

Out

No

TRACETRACEDATA changes on both the edges of TRACECLK.

TRACEDATA[3:0]

Out

No

Output data for clocked modes.

Table 4 • 

Port Details of the Cortex-M3-Subsystem

 (continued)

Port Name

Direction

Pad

Description

Summary of Contents for SmartFusion2 MSS






























































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartFusion2 MSS

Eaton SC300 Operation Handbook preview
SC300
Brand: Eaton Pages: 166
Value Point 3500 Quick Start Manual preview
3500
Brand: Value Point Pages: 7
Harman AMX JPK-1300 Quick Start Manual preview
AMX JPK-1300
Brand: Harman Pages: 2
T-Link TL300 Quick Install Manual preview
TL300
Brand: T-Link Pages: 3
Walimex Pro Excellence Instruction Manual preview
Excellence
Brand: Walimex Pro Pages: 68
SMC Networks VTA301 Series Operation Manual preview
VTA301 Series
Brand: SMC Networks Pages: 10
Baby Trend EZ Ride5 ST40 Instruction Manual preview
EZ Ride5 ST40
Brand: Baby Trend Pages: 12
Nuvoton NuMicro M252 Series User Manual preview
NuMicro M252 Series
Brand: Nuvoton Pages: 38
One for All Kameleon User Manual preview
Kameleon
Brand: One for All Pages: 15
Combi Ultra Savvy PM Instruction Manual preview
Ultra Savvy PM
Brand: Combi Pages: 16
Grosvenor RM-LUM-M320-IT/A Installation Manual preview
RM-LUM-M320-IT/A
Brand: Grosvenor Pages: 2
micro-trak Calc-An-Acre II Reference Manual preview
Calc-An-Acre II
Brand: micro-trak Pages: 30
IFM Ecomat100 CR1055 Mounting And Installation Instructions Manual preview
Ecomat100 CR1055
Brand: IFM Pages: 32
Contemporary Research ICA-FT6 Product Manual preview
ICA-FT6
Brand: Contemporary Research Pages: 22
Delta DZNT-104T Installation Manual preview
DZNT-104T
Brand: Delta Pages: 16
Pentair FLECK 5810 XTR2 Service Manual preview
FLECK 5810 XTR2
Brand: Pentair Pages: 36
HANYOUNG NUX TPR-3N Instruction Manual preview
TPR-3N
Brand: HANYOUNG NUX Pages: 4
zeeltronic PDCI-NS1V User Manual preview
PDCI-NS1V
Brand: zeeltronic Pages: 15

Brands by name

Popular brands

Load more brands