Microsemi PD-IM-7401 User Manual Download Page 13

Page: 13 / 14

PD-IM-7401 Evaluation Board - User Guide

Microsemi

Page

Rev. 1.0, 8-Apr-10

Analog Mixed Signal Group

2381 Morse Avenue, Irvine, CA 92614, USA; Phone (USA): (800) 713-4113, (ROW): (949) 221-7100 Fax: (949) 756-0308

5 Installation

This chapter describes the steps required to install and operate the Evaluation Board with any PoE application.

5.1

Preliminary Considerations and Safety Precautions

Verify that the board's power supply is turned on before the peripheral devices are turned on.

Prior to powering the board, connect all required peripherals.

Never hot swap units!

Verify that the board is properly configured prior to turning on the power supply.

5.2 Initial

Configuration

Note

: It is important to verify that the Evaluation Board is setup as shown in Figure 9 prior to starting any operation.

1. Connect the configuration board to the main board (J3).

2. Configure the board operation by selecting the required configuration on the configuration board switches
(SW#2).

3. Connect the SYC/UN-SYNC jumper (U3).

4. Connect a power cable from the power supply to the Evaluation Board (J2).

Ethernet

cable

Powered

Device

Power Supply

Power

Cable

Main DC

Input

Switch

Figure 9: Test Setup

Summary of Contents for PD-IM-7401















Search results

Summary of Contents for PD-IM-7401

Reviews:

Related manuals for PD-IM-7401

Brands by name

Popular brands

Microsemi PD-IM-7401, User Manual

Search results

Summary of Contents for PD-IM-7401

Reviews:

Related manuals for PD-IM-7401

Brands by name

Popular brands