Safety Information
Important Safety Information
♦
Installation and removal of the PoE Midspan must be
carried out by qualified personnel only.
♦
AC Power Cord Set:
o
The power cord must have regulatory agency
approval for the specific country in which it is being
used (i.e., UL, CSA, VDE, etc.).
o
The power cord must be a three-conductor type
(two current carrying conductors; one ground
conductor) terminated on one end by an IEC 60320
appliance coupler (for connection to the PoE
Midspan), and on the other end by a plug containing
a ground (earthing) contact.
o
The power cord must be rated for a minimum of
250Vac RMS operation, with a minimum rated
current capacity of 5 Amps (or a minimum wire
gauge of 18 AWG (0.75mm2).
: PoE Midspans installed in Australia require power
cords with a minimum wire gauge of 16 AWG (1.0 mm
2
).
: The PoE injector "Data In" and "Data & Power Out"
ports are shielded RJ45 data sockets. They cannot be used as
Plain Old Telephone Service (POTS) telephone sockets. Only
RJ45 data connectors may be connected to these sockets.
o
The AC wall socket-outlet must be near the PoE
Midspan and easily accessible. You can remove AC
power from the PoE Midspan by disconnecting the
AC power cord from either the wall socket-outlet or
the PoE Midspan appliance coupler.
o
The PoE Midspan Data In and Data & Power Out
interfaces are qualified as SELV (Safety Extra-Low
Voltage) circuits according to IEC 60950-1. These
interfaces can only be connected to SELV
interfaces on other equipment.
WARNINGS!
♦
Read the installation instructions before connecting the
PoE Midspan to its power source.
♦
Follow basic electricity safety measures whenever
connecting the PoE Midspan to its power source.
♦
A voltage mismatch can cause equipment damage and
may pose a fire hazard. If the voltage indicated on the
label is different from the power outlet voltage, do not
connect the PoE Midspan to this power outlet.
♦
The equipment is intended only for installation in a
Restricted Access Location/
Mounting Instructions
Perform the following:
1. Install two screws in the wall or shelf as shown below:
Figure 1: Mounting Instructions
2. Align the unit's mounting slots to capture the surface screws
3. Connect the ground studs as shown below:
Stud diameter = 5 mm
Connect this side
To earth ground
Stud diameter = 5 mm
Figure 2: Stud Connection to Ground
Recycling and Disposal
Disposal instructions for old products. The WEEE (Waste Electrical
and Electronic Equipment) national environmental initiatives has
been put in place to ensure that products are recycled using best
available treatment, recovery and recycling techniques to ensure
human health and high environmental protection. Your product is
designed and manufactured with high quality materials and
components, which can be recycled and reused. Do not dispose of
your old product in your general household waste bin. Inform
yourself about the local separate collection system for electrical and
electronic products marked by this symbol:
Use one of the following disposal options :
1. Dispose of the complete product (including its cables, plugs
and accessories) in the designated WEEE collection facilities.
2. If you purchase a replacement product, hand your complete
old product back to the retailer. He should accept it as required
by the national WEEE legislation.
Ordering information:
•
Product Name:
Microsemi 9001G-40/SP
•
Part Number:
PD-9001G-40/SP/AC
•
Description:
1-Port 802.3at 40W Gigabit PoE Midspan with
Surge Protection
Document P/N 06-0062-056 Rev. C00
M
M
i
i
c
c
r
r
o
o
s
s
e
e
m
m
i
i
9
9
0
0
0
0
1
1
G
G
-
-
4
4
0
0
/
/
S
S
P
P
U
U
s
s
e
e
r
r
G
G
u
u
i
i
d
d
e
e
1
1
-
-
P
P
o
o
r
r
t
t
8
8
0
0
2
2
.
.
3
3
a
a
t
t
4
4
0
0
W
W
G
G
i
i
g
g
a
a
b
b
i
i
t
t
P
P
o
o
E
E
M
M
i
i
d
d
s
s
p
p
a
a
n
n
w
w
i
i
t
t
h
h
S
S
u
u
r
r
g
g
e
e
P
P
r
r
o
o
t
t
e
e
c
c
t
t
i
i
o
o
n
n
Notice
It is Microsemi’s policy to improve its products as new
technology, components, software, and firmware
become available. Microsemi, therefore, reserves the
right to change specifications without prior notice.
Technical Support
If you encounter problems when installing or using this
product, please consult the Microsemi website at:
http://www.microsemi.com
For technical support, call: +972-9-775-5123
In the USA: 1-877-480-2323
Microsemi Corp.
Covered under one or more of US Patents:
#7,006,815; and 7,437,217.
