background image

Important note: If you change “Source” field for a channel, you also need to change 

“Name”, “Units”, and “Coeffs” fields. Otherwise everyone elso who receive your data 
(including web services like aprs.fi) will not be able do decode your reports properly.

Every source has its own coefficients, names and units. With USB Configurator you can 
get   default   settings   by   clicking   on   “Default   parameters”   button.   When   changing 

configuration via WWW you need to set these fields manually (you can always write 
them down from USB Configurator application).

Digital channels:

“Digital  channels   1-4”

  and  

“Digital  channels   5-8”

  Tabs  –  define  8   digital  channels 

available in APRS telemetry reports. These tabs should be used when WXBits module is 

connected,

“Name”

 - short name for the channel, length is limited by APRS standard and is 

different for different channel numbers,

“Label”

 - short label for the channel, length is limited by APRS standard and is 

different for different channel numbers,

“Source”

 - most important field, specifies what data will be send for particular 

channel, (M) sources are associated with WXBits module,

“Inverted”

 - defines if channels should be reported as inverted in BITS telemetry 

message,

“Default parameters”

 – you should click this button after you change data source 

for the channel. It loads default coefficient values and name/units for a channel.

Important note: If you change “Source” field for a channel, you also need to change 
“Name”, “Label”, and “Inverted” fields. Otherwise everyone else who receive your data 

(including web services like aprs.fi) will not be able do decode your reports properly.

22

Summary of Contents for PLXDigi

























Reviews: