BEFORE USING FOR THE FIRST TIME
If necessary, wipe the kettle with a damp cloth and dry thoroughly.
When using for the first time, consult the list of Dos and Don’ts listed in section 5. When you
have read them, you will need to boil away any impurities that have collected during
transport. To do this, follow the instructions in section 2. When the kettle has boiled, pour the
water away, wash and rinse the inside of the kettle before using again. The kettle is now
ready for use.
WARNING:
DO NOT FILL ABOVE THE ‘FULL’ LINE INSIDE THE KETTLE AS THERE IS
DANGER OF BOILING WATER SPILLING OUT OF THE KETTLE.
USING THE KETTLE
1.
Remove the lid from the kettle.
2.
Fill the kettle with water ensuring that the element is completely covered and that the water
does not exceed the ‘FULL’ level marked inside the kettle (Figure 1).
3.
Replace the kettle lid and point the arrow (embossed on the lid) towards the on/off switch
to prevent the lid lifting when pouring (Figure 2).
4.
Plug the mains lead into the kettle and then into a suitable mains outlet socket.
5.
Switch on the mains socket and press the kettle ON/OFF switch to switch the kettle on.
6.
When the water boils the kettle will automatically switch off.
If you require warm water only, you can press the ON/OFF switch to the OFF position
before the water boils.
7.
Unplug the kettle from the power supply before pouring the boiling water and whenever the
kettle is not being used.
8.
Allow the kettle to cool before boiling any more water.
CLEANING AND CARE FOR YOUR KETTLE
Rinse the kettle regularly to remove any loose scale. The kettle should be regularly de-scaled
using a proprietary brand descaler purchased from any good hardware store. The period
between cleaning will depend upon water hardness and how often the kettle is used.
Use a damp cloth to clean the kettle exterior. Abrasive cleaning products should not be used
as they can scratch the surface.
Your kettle will last longer if it is emptied every time after it has been used.
The element may discolour after some time, but this will not effect the performance of the
kettle.
REMOVE PACKAGING MATERIALS FROM THE PRODUCT BEFORE ATTEMPTING TO USE IT
WIRING INSTRUCTIONS
WARNING: THIS APPLIANCE MUST BE EARTHED.
This product is supplied with a moulded plug which contains a 13A fuse. If you are simply
replacing the fuse, you must use a 13A fuse which has been approved by ASTA to BS1362.
If the fuse cover is detached, never use the plug with the cover omitted.
If the plug does not fit the socket or becomes damaged, a new plug must be fitted. Replace the
original plug with the correct plug for your socket. If this is a 3-pin (square pin) 13A (BS1363)
plug, you must make sure that it is fitted with an ASTA approved 13A fuse.
If another type of plug is used, it must be protected
by a 13A fuse, either in the plug or at the
distribution board.
1. Cut off the existing fitted plug.
2. The wires in the mains lead supplied with this
appliance are coloured in accordance with the
following code:
GREEN/YELLOW = EARTH (E)
BLUE = NEUTRAL (N) BROWN = LIVE (L)
This product must be earthed.
As the colours of the wires in the mains lead may
not correspond with the colour markings identifying
the terminals in your new plug, proceed as follows.
The wire which is coloured GREEN or YELLOW/GREEN must be connected to the terminal
which is marked with the letter E or
E
symbol or coloured GREEN or YELLOW/GREEN.
The wire which is coloured BLUE must be connected to the terminal in the plug which is
marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal which is marked with
the letter L or coloured RED.
3. Ensure that the connections are tight and that no loose strands are left out of the terminals.
IF IN ANY DOUBT CONSULT A QUALIFIED ELECTRICIAN.
Do not attempt to replace or repair the mains cable yourself, consult a qualified
electrician.
DOS AND DON’TS
•
Do disconnect the kettle from the mains supply when filling or pouring, and when not in use.
•
Do take care to pour boiling water slowly and carefully, without tipping the kettle too fast.
•
Do ensure that the kettle is used on a firm, flat surface.
•
Do avoid contact with steam from the spout when the water is boiling or just after it has
switched off.
•
Do keep the outside of the kettle clean and dry at all times.
•
Do make sure that small children cannot reach the kettle and that the mains lead does not
hang over the edge of the table or work surface.
•
Do ensure that children are aware of the dangers of boiling water, and supervise them
carefully.
IN THE EVENT OF AN ACCIDENT: If a scald occurs, run cold water over the affected area
immediately.
• Do not stop to remove clothing; get medical help as soon as possible
• Don’t remove the kettle lid whilst the water is boiling.
• Don’t fill the kettle above the ‘FULL’ mark. If the kettle is overfilled, boiling water may be
ejected.
•
Don’t immerse the kettle or mains lead in water.
•
Don’t use in the vicinity of a bath, shower, swimming pool or damp environment.
•
Don't use abrasive cleaners on the outside of the kettle – these will scratch the surface.
Clean with a soft damp cloth.
•
Don’t tamper with the ON/OFF button or fix it to the ‘ON’ position.
•
Don't use the kettle for any use other than to boil water.
•
Don’t let the mains lead or kettle come onto contact with hot surfaces or naked flames.
4
5
WIRING THE 3-PIN PLUG
YELLOW/GREEN
(EARTH)
BROWN
(LIVE)
CABLE
GRIP
BLUE
(NEUTRAL)
2
3
1
FIGURE 1
FIGURE 2
ON/OFF
SWITCH
‘FULL’ INDICATOR
MARK (DO NOT FILL
ABOVE THIS LEVEL)
ARROW
SOCKET FOR
MAINS
CONNECTING
LEAD
KETTLE
LID
