microjig DVC-1177K2 Instruction Manual Download Page 19 | Manualshive

Page: 19 / 20

microjig DVC-1177K2 Instruction Manual Download Page 19

-  Lay the sled flat on the table surface and set your rip fence to 10-1/8”,
  leaving a small gap between the sled and the blade.
-  Clamp your workpiece to the sled. Make sure that your clamps are spread
  out in the tracks available in order to secure the entire workpiece.
-  Once the Dovetail Clamps are tightened, the bars can be used as handles
  to advance the sled and workpiece through the cut.

COMBO TALL FENCE / JOINTING SLED PLANS

USING AS A JOINTING SLED

There’s no limit to what you can build with the MATCHFIT System. The only
question is, “Where to start?” Visit microjig.com/matchfitprojects to access
our library of free jig plans and tutorial videos.

WORK SAFER. WORK SMARTER.

We hope that you enjoy these project plans and learn a few new tricks to use

in your shop. Share photos of your completed project with us on Facebook, Twitter

and Instagram with hashtag

#worksmarter

Facebook.com/microjig • Twitter.com/microjig • Instagram: @microjig

FREE DOWNLOADABLE JIG PLANS

Scan this QR code for access to our library of free jig plans

and for more information about the MATCHFIT 360 System.

www.microjig.com/matchfitprojects

19

«
...
17
18
19
20
»

Summary of Contents for DVC-1177K2





















Reviews:

No comments