Microhard Systems IP920 Operating Manual Download Page 6 | Manualshive

Page: 6 / 73

Microhard Systems IP920 Operating Manual Download Page 6

iv

IP920 Operating Manual: Contents

4.8.2

Reset Radio to Defaults........................................................................................................................................................................43

4.8.3

Reboot System ......................................................................................................................................................................................43

4.8.4

Reset System to Default........................................................................................................................................................................43

5.

INSTALLATION...............................................................................................................................................45

5.0

O

VERVIEW

..................................................................................................................................................................... 45

5.1

E

STIMATING THE

G

AIN

M

ARGIN

..................................................................................................................................... 45

5.2

I

NSTALLING

E

XTERNAL

C

ABLES

,

A

NTENNAS AND

L

IGHTNING

A

RRESTORS

...................................................................... 47

A.

SERIAL INTERFACE..................................................................................................................................51

B.

RS485 WIRING .............................................................................................................................................53

2-wire RS-485......................................................................................................................................................................................................53

4-wire RS-485......................................................................................................................................................................................................53

C.

MOUNTING DIMENSIONS........................................................................................................................55

D.

TECHNICAL SPECIFICATIONS ..............................................................................................................57

E.

APPROVED ANTENNAS ............................................................................................................................59

F.

GLOSSARY ...................................................................................................................................................61

«
...
4
5
6
7
8
...
»

Summary of Contents for IP920










































































Reviews:

No comments