manualshive.com logo in svg

Microflex Microlink-HM+, Installation, Operation, Specifications, Page: 9 / 10

Share
Download
Microflex Microlink-HM+ Installation, Operation, Specifications Download Page 9

Default Settings

 

Serial Port .........................................................................................RS-485 Mode, 1200 Baud, Odd Parity, 1 Stop  

 Modbus 

Address 

................................................................................................................................................... 1

 

Fill Modbus Registers ..............................................................................Disabled (HART Protocol Modem Mode)

 Poll 

Interval 

............................................................................................................................................. 2 Seconds

Environmental

 Opera  ng Temperature ............................................................................................-30°C to 60°C (-22°F to 140°F)
 

Storage Temperature ...............................................................................................-40°C to 85°C (-40°F to 185°F)

 Humidity 

...................................................................................................................... 0 to 95% (non-condensing)

Enclosure

 

Polycarbonate  plas  c with Stainless Steel Cover

 Weight 

....................................................................................................................................................2.3 ounces

 Moun  ng ................................................................................................................................. 35mm DIN Rail Clip

8

2.45

62.3 mm

3.32

84.2 mm

1.58

40.1 mm

1.03

26.2 mm

.42

10.6 mm

1.66

42.2 mm

SN: 123456

Summary of Contents for Microlink-HM+











Reviews:

No comments