Microflex 101-0028 Operation Manual Download Page 8

Limited Warranty

Micro

fl

 ex, LLC warrants this unit against defects in materials and 

workmanship for a period of one year from the date of shipment.  Micro

fl

 ex, 

LLC will, at its option, repair or replace equipment that proves to be defective 
during the warranty period.  This warranty includes parts and labor.

A Return Authorization (RA) number must be obtained from the factory 
and clearly marked on the outside of the package before equipment will be 
accepted for warranty work.

Micro

fl

  ex, LLC believes that the information in this manual is accurate.  In the 

event that a typographical or technical error exist, Micro

fl

 ex, LLC reserves 

the right to make changes without prior notice to holders of this edition.  
The reader should consult Micro

fl

 ex, LLC if any errors are suspected.  In no 

event should Micro

fl

 ex be liable for any damages arising out of or related to 

this document or the information contained in it.

EXCEPT AS SPECIFIED HEREIN, MICROFLEX, LLC MAKES 
NO WARRANTIES OR MERCHANTABILITY OR FITNESS FOR 
A PARTICULAR PURPOSE.  CUSTOMER’S RIGHT TO RECOVER 
DAMAGES CAUSED BY FAULT OR NEGLIGENCE ON THE PART 
OF MICROFLEX, LLC SHALL BE LIMITED TO THE AMOUNT 
THERETOFORE PAID BY THE CUSTOMER.  MICROFLEX, LLC 
WILL NOT BE LIABLE FOR DAMAGES RESULTING FROM 
LOSS OF DATA, PROFITS, USE OF PRODUCTS, OR INCIDENTAL 
OR CONSEQUENTIAL DAMAGES, EVEN IF ADVISED OF THE 
POSSIBILITIES THEREOF.  This limitation of the liability of Micro

fl

 ex will 

apply regardless of the form of action, whether in contract or tort, including 
negligence.  Any action against Micro

fl

 ex, LLC must be brought within 

one year after the cause of action accrues.  The warranty provided herein 
does not cover damages, defects, malfunctions, or service failures caused by 
owners failure to follow Micro

fl

 ex’s installation, operation, or maintenance 

instructions; owners modi

fi

 cation of the product; owner’s abuse, misuse, or 

negligent acts; and power failure or surges, 

fi

 re, 

fl

 ood, accident, actions of 

third parties, or other events outside reasonable control.

Micro

fl

 ex, LLC

2202 Red Bird Lane
Brookshire, Texas 77423
USA

Phone 281-855-9639
Fax 832-422-4391
www.micro

fl

 x.com

Summary of Contents for 101-0028









Reviews: