Microchip Technology BM83 EVB, User Manual

Page: 63 / 73

12. Appendix F: Hardware Setup for Application Demo in Host MCU Mode
Note: The host MCU (on-board PIC32 MCU) is connected to the BM83 module over UART. The host MCU is
controlling the BM83 module and driving the I2S audio out from the BM83 to an STA369BW Audio Daughter Board.
Perform the following hardware changes for the Host MCU mode application demo:
Note: To locate these switches, jumpers, and headers on the BM83 EVB, refer to Figure 2-1 and Figure 3-2 .
1. Mount a jumper on the pin2 (3V3_IO) and pin3 (VDDIO) of JP305.
2. Set the SW200 switch to 5V_DC position to enable the 5V supply to ADAP_IN.
3. Mount a jumper on the 3V3_GEN pin and 3V3_PIC pin of the JP400 to enable 3.3V to PIC.
4. Jumper settings on J402 and J403 to enable BM83 module to control DSP (audio codec):
4.1.
Mount a jumper on pin1 of J402 and J403.
4.2. Mount a jumper on pin2 of J402 and J403.
4.3. Mount a jumper on pin3 of J402 and J403.
4.4. Mount a jumper on pin4 of J402 and J403.
4.5. Mount a jumper on pin5 of J402 and J403.
4.6. Mount a jumper on pin6 of J402 and J403.
4.7. Open pin7 of J402 and J403.
5. Jumper settings on J700 and J701 to enable BM83 module to control the audio control buttons:
5.1.
Mount a jumper on pin1 of J700 and J701.
5.2. Mount a jumper on pin2 of J700 and J701.
5.3. Mount a jumper on pin3 of J700 and J701.
5.4. Mount a jumper on pin4 of J700 and J701.
5.5. Mount a jumper on pin5 of J700 and J701.
5.6. Mount a jumper on pin6 of J700 and J701.
5.7. Mount a jumper on pin6 of J700 and J701.
5.8. Open pin8 of J700 and J701.
6. Mount a jumper on pin2 and pin3 of JP201.
7. Set SW400 switches as follows:
7.1.
RFS1_DSP to OFF position.
7.2. SCLK1 to OFF position.
7.3. DT1_DSP to OFF position.
7.4. MCLK1_DSP to OFF position.
7.5. LINE_IN_DET to ON position.
7.6. P3_2 to OFF position.
8. Set SW402 switches as follows:
8.1.
MFB to OFF position.
8.2. HCI_RXD to ON position.
8.3. HCI_TXD to ON position.
8.4. RST_N to OFF position.
8.5. P0_0 to ON position.
8.6. P3_4 to ON position.
9. Set SW403 switches as follows:
9.1.
P3_7 to ON position.
9.2. P2_6 to OFF position.
9.3. P2_3 to OFF position.
9.4. RFS1 to OFF position.
9.5. SCLK1 to OFF position.
9.6. DT1 to OFF position.
10. Jumper settings on J404 and J405 to connect BM83 module and STA369BW codec (ST) over I2S interface:
BM83 EVB
Appendix F: Hardware Setup for Application Dem...
©
2019 Microchip Technology Inc.
User Guide
DS50002902A-page 63