MICRO-EPSILON scanCONTROL2800 Instruction Manual Download

Page: 36 / 42

MICRO-EPSILON

X9751109-B060097MSC

Software

11.

Software

You can find the description of the setup program, the software/measuring program on
the delivered compact disk.

A DLL is available to integrate the scannCONTROL28x0 into extensive measuring
programs. This function is included on the CD too.

12.

Decommissioning, Disposal

- Disconnect the power supply on the controller.

- Disconnect the cables between sensor, controller and consecutively control and
process units.

The scanCONTROL28x0 is produced according to the directive 2002/95/EC („RoHS“).
The disposal is done according to the legal regulations (see directive 2002/96/EC).

13.

Annex

13.1

Accessory

CE2800-3-SB

Extension cable for sensor; 3.0 m long, qualified for drag chain use
(female-male)

CE2800-3-SS

Connection cable for sensor; 2.75 m long, qualified for drag chain
use (male-male)

CE2800-5-SB

Extension cable for sensor; 5 m long, qualified for drag chain use
(male-male)

CE2800-5-SS

Connection cable for sensor; 4.75 m long, qualified for drag chain
use (male-male)

CE2800-8-SB

Extension cable for sensor; 8 m long, qualified for drag chain use
(male-male)

CE2800-8-SS

Connection cable for sensor; 7.75 m long, qualified for drag chain
use (male-male)

CE2800-10-SS

Connection cable for sensor; 9.75 m long, qualified for drag chain
use (male-male)

CER2800-5-SS

Connection cable for sensor; 4.75 m long, qualified for robotic use
(male-male)

CER2800-8-SB

Extension cable for sensor; 8 m long, qualified for robotic use
(female-male)

CER2800-8-SS

Connection cable for sensor; 7.75 m long, qualified for robotic use
(male-male)

CER2800-10-SS

Connection cable for sensor; 9.75 m long, qualified for robotic use
(male-male)

PC2800-3

Power supply cable, 3 m long

SCD-IEEE-1394-3

FireWire-Cable, 3 m long

SC2800-0,5

Synchronization cable, 0.5 m long, for 2D - Laser displacement
systems scanCONTROL, suitable for scanCONTROL28x0

PS2010

Power supply, input 210 - 240 VAC (or 110-120 VAC), output
24 VDC, for snap in mounting on DIN 50022 rail

IF2800-Matrox

Matrox PCI-Adapter-Board, Meteor 2-1394, PCI interface card for
Personal Computer, FireWire (IEEE1394) for scanCONTROL28x0

Summary of Contents for scanCONTROL2800











































Search results

Summary of Contents for scanCONTROL2800

Reviews:

Related manuals for scanCONTROL2800

Brands by name

Popular brands

MICRO-EPSILON scanCONTROL2800, Instruction Manual

Search results

Summary of Contents for scanCONTROL2800

Reviews:

Related manuals for scanCONTROL2800

Brands by name

Popular brands