background image

18 

©2022 Micro-Air Corp 

 

March 21, 2022, revision 1.0 

Schedule Screens 

The schedule supports 7 day per week scheduling of events. Events can include changes to the set 

point or mode of operation for one or more zones

Figure 3 

shows the main schedule screen. 

 

The smart device application also offers a method to copy days. Once a schedule is set for one 

day, it can be copied to any other day. 

(1) Day of the Week 

Day of the week is selected from the days along the top of 
the screen. The day selected appears in white. 

(2) Scheduled Events 

Events  are  numbered  1  to  6  along  the  left  side  of  the 
display.  Tap  an  event  to  edit  it  and  advance  to  the 
schedule edit screen, shown in 

Figure 4

. Tap 

“more” to see 

events 4, 5, and 6. 

(3) System Time 

System time is displayed along the bottom. Tap the time 
to change from 12-hour to 24-hour time format. 

A “

--:--

” 

is shown when time has yet to be set. See section 

Local 

Weather and Local Time

 for setting up the system time.  

(4) Back 

Tap the back arrow to return to the last screen. 

 

 

Figure 3 - Main Schedule Screen 

Summary of Contents for ASY-356-X01
























Reviews: