manualshive.com logo in svg

Micrel KSZ8873FLL, User Manual, Page: 8 / 10

Share
Download
Micrel KSZ8873FLL User Manual Download Page 8

KSZ8873MLL/FLL/RLL Evaluation Board User’s Guide 

 

Micrel, Inc. 

 

January 11, 2011 

Confidential 

 

Rev. 1.1 

8/10

 

 

5.  The  KSZ8873MLL/FLL/RLL  will  power  up  in  its  default  configuration  if  there  is  no 

information in the EEPROM. 

6.  Click the software icon to invoke the software to program the desired settings into the 

             EEPROM. See the Micrel Switch Configuration Software User Guide for details. 

7.  Press the manual reset button. The KSZ8873MLL/FLL/RLL will reset and read the new 

            configuration in the EEPROM. After reset, the KSZ8873MLL/FLL/RLL is ready for normal  
            operation.  

 

Table 3: EEPROM Mode Settings 

Jumper 

Description 

Setting 

JP9 

SPIQ 

Closed 

JP3 

SCL_MDC_SW 

Closed 

JP34 

SCL_MDC 

Closed 

JP35 

SDA_MDIO 

Closed 

JP25 

Serial Bus Config. (P2LED0) 

Pins 2-3 closed 

JP21 

Serial Bus Config. (P2LED1) 

Pins 2-3 closed 

 
 

4.3  SPI Slave Mode 

 

From SPI interface to the KSZ8873MLL/FLL/RLL, use a USB to SPI converter that 
allows accessing all of the KSZ8873MLL/FLL/RLL features and registers. The user can 
easily access the SPI interface using a computer connected to the evaluation board’s USB 
port interface. Micrel provides a Windows 2000/XP based program for the user to 
evaluate the KSZ8873MLL/FLL/RLL’s full feature set.  In addition to all the registers 
available via EEPROM programming, a host CPU connected to the 
KSZ8873MLL/FLL/RLL’s SPI interface will be able to access all static MAC entries, the 
VLAN table, dynamic MAC address table and the MIB counters.  

To prepare the KSZ8873MLL/FLL/RLL evaluation board for SPI mode 
configuration follow these steps:  
 

1.  Install the Micrel Switch Configuration Software on your computer.  
2.  Set JP3, JP9, JP21, JP25, JP34 and JP35 as specified in Table 4 for SPI mode 
configuration.  

Table 4: SPI Slave Mode Settings 

Jumper 

Description 

Setting 

JP9 

SPIQ 

Open 

JP3 

SCL_MDC_SW 

Open 

JP34 

SCL_MDC 

Closed 

JP35 

SDA_MDIO 

Closed 

JP25 

Serial Bus Config. (P2LED0) 

Pins 2-3 closed 

JP21 

Serial Bus Config. (P2LED1) 

Pins 1-2 closed 

3.

 

Connect the computer’s USB port to the KSZ8873MLL/FLL/RLL board with a 

Summary of Contents for KSZ8873FLL











Reviews:

No comments