Micha Solar MSRx User'S Operation Manual Download Page 30 | Manualshive

Page: 30 / 46

Micha Solar MSRx User'S Operation Manual Download Page 30

Micha Solar

MSRx Charge Controller

User Operation Manual

Page 30 of 46

Document: 802440-30.doc

Date: December 2020

www.micha.co.uk

Menu E Notes:

Menu E Screen 0-5 – Expansion Port Modules:

For full details of the Expansion Port Modules and the Settings Menu, see Section 6

Menu E Screen 13 – Battery Temperature Charging Function:

Disable Charging on Battery Temperature Function = Off:

No change to charge controller operation

Disable Charging on Battery Temperature Function = On:

If the Battery Temperature is greater than or equal to the High Temperature Parameter (set using Menu
E Screen 13), then Battery Charging will be disabled.

If the Battery Temperature is equal to or less than the Low Temperature Parameter (set using Menu E
Screen 14), then Battery Charging will be enabled.

Menu E Screen 14 – Battery Temperature Charging High Temperature Parameter:

Disable Charging If Battery Temperature is greater than or equal to High Temperature Parameter

Parameter can be adjusted from 1-70°C (default = 60°C)

Menu E Screen 15 – Battery Temperature Charging Low Temperature Parameter:

Enable Charging If Battery Temperature is less than or equal to Low Temperature Parameter

Parameter can be adjusted from 0-69°C (default = 58°C)

«
...
28
29
30
31
32
...
»

Summary of Contents for MSRx















































Reviews:

No comments