background image

Operator’s Manual  

29

EXHAUST AND EVAPORATIVE EMISSIONS CONTROL WARRANTY STATEMENT 

YOUR WARRANTY RIGHTS AND OBLIGATIONS 

The California Air Resources Board, the United States Environmental Protection Agency (EPA) and Mi-T-M are pleased to 

explain the emission control system’s warranty on your 2022/2023 small off-road engine/equipment (SORE). In California, new 
equipment that use small off-road engines must be designed, built and equipped to meet the State’s stringent anti-smog standards. Mi-
T-M must warrant the exhaust and evaporative emissions control system (E & EECS) on your SOREs for the period listed below 
provided there has been no abuse, neglect or improper maintenance of your equipment leading to the failure of the evaporative 
emission control system. 

Your E & EECS may include parts such as the carburetor, fuel tanks, fuel lines (for liquid fuel and fuel vapors), fuel caps, valves, 

canisters, filters, clamps, connectors, and other associated components. Where warrantable conditions exist, Mi-T-M will repair your 
small off-road engine at no cost to you including diagnosis, parts and labor. 

MANUFACTURER’S WARRANTY COVERAGE: 
This E & EECS is warranted for two years. If any evaporative emissions-related part on your small off-road engine/equipment is 

defective, the part will be repaired or replaced by Mi-T-M. 
OWNER’S WARRANTY RESPONSIBILITIES: 

 

-As the SORE owner, you are responsible for performance of the required maintenance listed in your owner’s manual. Mi-T-M 
recommends that you retain all receipts covering maintenance on your SORE , but Mi-T-M cannot deny warranty coverage solely 
for the lack of receipts. 

 

-As the SORE owner, you should be aware that Mi-T-M may deny you warranty coverage if your SORE or a part has failed due to 
abuse, neglect, or improper maintenance or unapproved modifications. 

 

-You are responsible for presenting your SORE to distribution center or service center authorized by Mi-T-M Corporation, 50 Mi-T-
M Drive, Peosta, IA 52068 (herein Mi-T-M) as soon as the problem exists. The warranty repairs shall be completed in a reasonable 
amount of time, not to exceed 30 days. 

If you have a question regarding your warranty coverage, you should contact Mi-T-M Customer Service Department at 1-800-

553-9053 or by emailing us at [email protected]

GENERAL EMISSIONS WARRANTY COVERAGE 

MI-T-M WARRANTS TO THE ULTIMATE PURCHASER AND EACH SUBSEQUENT PURCHASER THAT THE SORE (1) HAS BEEN 

DESIGNED, BUILT AND EQUIPPED SO AS TO CONFORM WITH ALL APPLICABLE REGULATIONS; AND (2) IS FREE FROM 

DEFECTS IN MATERIALS AND WORKMANSHIP THAT CAUSE THE FAILURE OF A WARRANTED PART TO CONFORM WITH 

THOSE REGULATIONS AS MAY BE APPLICABLE TO THE TERMS AND CONDITIONS STATED BELOW. 

(a) The warranty period begins on the date the engine is delivered to an ultimate purchaser or first placed into service. The warranty 

period is two years. 

(b) Subject to certain conditions and exclusions as stated below, the warranty on emissions related parts is as follows: 
 

(1)  Any warranted part that is not scheduled for replacement as required maintenance in your owner’s manual is warranted for the 
warranty period stated above. If the part fails during the period of warranty coverage, the part will be repaired or replaced by Mi-T-
M according to subsection (4) below. Any such part repaired or replaced under warranty will be warranted for the remainder of the 
period. 

 

(2)   Any warranted part that is scheduled only for regular inspection in your owner’s manual is warranted for the  warranty period 
stated above. Any such part repaired or replaced under warranty will be warranted for the remaining warranty period. 

 

(3)   Any warranted part that is scheduled for replacement as required maintenance in your owner’s manual is warranted for the 
period of time before the first scheduled replacement date for that part. If the part fails before the first scheduled replacement, the 
part will be repaired or replaced by Mi-T-M according to subsection (4) below. Any such part repaired or replaced under warranty 
will be warranted for the remainder of the period prior to the first scheduled replacement point for the part. 

 

(4)   Repair or replacement of any warranted part under the warranty provisions herein must be performed at a warranty station at 
no charge to the owner. 

 

(5)   Not withstanding the provisions herein, warranty services or repair will be provided at all of our distribution centers that are 
franchised to service the subject engines. 

 

(6)   The owner must not be charged for diagnostic labor that leads to the determination that a warranted part is in fact defective, 
provided that such diagnostic work is performed at a warranty station. 

 

(7)   Throughout the engine warranty period stated above, Mi-T-M will maintain a supply of warranted parts sufficient to meet the 
expected demand for such parts. 

 

(8)   Any replacement parts that do not increase the exhaust or evaporative emissions of the engine or evaporative emission control 
system must be used in the performance of any warranty maintenance or repairs and must be provided without charge to the 
owner. Such use will not reduce the warranty obligations of Mi-T-M. 

 

(9)  Add-on or modified parts that are not exempted by the Air Resources Board may not be used. The use of any non-exempted 
add-on or modified parts by the ultimate purchaser will be grounds for disallowing a warranty claims. Mi-T-M will not be liable to 
warrant failures of warranted parts caused by the use of a non-exempted add-on or modified part.  

 

(10) Mi-T-M shall provide any documents that describe that Mi-T-M warranty procedures or policies within five working days of 
request by the Executive Officer. 

Summary of Contents for GEN-3500-iMM1































Reviews: