MGG HT-023 Operator'S Manual Download Page 2 | Manualshive

Page: 2 / 15

MGG HT-023 Operator'S Manual Download Page 2

2

Package Contents:



Operator’s Manual



1 x Indoor wall-mounted transmitter



4 x screws



1 x Mains adaptor



1 x Adjustable dog collar-receiver



1 x 6-volt battery for collar-receiver



1 x Test light bulb for collar-receiver



2 x Long length metal probes



2 x Short length metal probes



Boundary wire



20 x Training flags

Other items you may need:



Screwdriver



Straight edged spade or a lawn edger



Wire stripping pliers



Electrical tape



Waterproofing compound (e.g. silicone caulking)



Patching compound for your type of path or driveway



PVC pipe if crossing a gravel driveway, pond or lake



Pencil, paper, ruler or protractor



Drill with appropriate drill bit if drilling through concrete or wood is required



Additional boundary wire with waterproof connectors

About the Operators Manual:

This manual is divided into 3 sections:



Section 1: Instructions for installing your MGG Hidden Fencing System



Section 2: Training your dog with the system



Section 3: Troubleshooting, maintenance and contact information

Please read the Operator’s Manual fully before installing this product. For the safety of your dog
you  should  follow  the  comprehensive  training  programme.    If  your  dog  does  not  receive
adequate  training  it  will  not  understand  the  initial  audio  warning  from  the  collar-receiver  not  to
proceed  and  may  become  confused,  frustrated  and  even  frightened  if  it  is  subjected  to
numerous static corrections which will also considerably shorten the collar-

receiver’s battery life.

Caution:



KEEP OUT OF REACH OF CHILDREN



NEVER perform any tests of the system with the collar-receiver on your dog. Full
instructions are enclosed for manual testing



Never leave the collar-receiver on your dog for more than 12 hours per day



The collar-

receiver should only be used under close supervision by the dog’s owner



The collar-receiver can withstand light showers but is NOT WATERPROOF and should not
be submerged in water, either through swimming or rolling in puddles etc.



This system is intended for use on dogs

Important: Before installing your system we recommend conducting a Quick System
Test to ensure all components are working

«
1
2
3
4
...
»

Summary of Contents for HT-023
















Reviews:

No comments