MGG HT-023 Operator'S Manual Download Page 1

 

 

 

MGG Radio Controlled Hidden Fencing System for Dogs  

 

Operator’s Manual for Model no: HT-023 

 
 

This  MGG  hidden  fencing  system  is  among  the  most  reliable,  cost-efficient  dog  containment 
systems  available  today.    A  buried  boundary  wire  transmits  a  harmless  radio  signal  which 
activates  the  dog’s  collar-receiver  whenever  your  dog  approaches  the  boundary.    An  initial 
warning  beep  is  delivered  as  a  correction  to  your  dog.    If  your  dog  continues  closer  to  the 
boundary,  the  system  will  issue  a  mild  static-stimulation.    Should  your  dog  progress 
further,  the  system  will  administer  stronger  static-stimulations  until  your  dog  returns  to  within 
the boundary radius you have set.  Your dog will naturally seek to avoid this type of correction and 
will be content to stay within the established boundaries. 
 

Main Features include: 
Progressive Tone Stimulus 

 

A warning tone will be issued first, followed by a static-stimulation if your dog continues to move 
closer to the boundary 

Pulsed Proportional Stimulus

 

The closer your dog is to the boundary, the more intense the static-stimulation will be 

Speed Detect Anti-Run through

 

The faster your dog is moving, the quicker and higher the level of intensity issued 

Variable Field Width Control

 

Allows you to precisely control the width of the signal field 
 

Audible and Visual Wire Break Indicators 

Should  your  buried  boundary  wire  ever  break,  a  sonic  alarm  will  sound  accompanied  by  a 
flashing light on the wall transmitter 

 
Built-in Lightning Protection 

Protects the wall transmitter from power surges caused by lightning strikes 

Multiple Collar-Receiver Operation 

Add as many collar-receivers as you like to contain any number of dogs you have.  There is no 
limit to the number of collar-receivers the system can control 
 

Range 

Up to a 5000 square metre range, equivalent to over 1.2 acre 
 

Use 

Suitable for most dog breeds.   The weight  of the collar-receiver is  only 66grams including the 
battery and can be used with smaller sized dogs 

Summary of Contents for HT-023
















Reviews: