2
3
1. Slide the ON/OFF switch on the bottom of the
Cruiser
to the “ON” position.
2. Slide the ON/OFF switch on the back of the Remote Control to the “ON” position.
3. Place the
Cruiser
on a flat, level surface.
4. Straighten the Antenna.
5. Use the Remote Control to drive your
Cruiser
by doing the following:
a. Press down on the left side of the Remote Control to go forward. (Fig. 5)
b. Press down the right side of the Remote Control to back up and turn to the left. (Fig. 6)
• When driving two RC
Cruiser
, they must be of different radio frequencies (e.g. one
Cruiser
49MHz and
one
Cruiser
27MHz) or they may not perform as designed.
• When
Cruiser
is not being played with, turn the ON/OFF switches on both the
Cruiser
and Remote “OFF”
to save battery power.
• Your
Cruiser
is controlled by radio frequency. It may interfere with nearby devices such as cordless
phones, hair dryers, radios, walkie-talkies, or other radio controlled devices. If this occurs, move the
Cruiser
to a location away from the interference.
• The
Cruiser
must remain in remote control range to operate correctly. The range depends on the
surrounding area and on the strength of the battery. Obstructions such as buildings, fences, etc., between
the remote control transmitter and the
Cruiser
, reduce the range.
• If the
Cruiser
runs slowly, replace the batteries.
• KEEP AWAY FROM WATER! Do not run your
Cruiser
through puddles, or expose it to liquid of any kind as
moisture may damage the unit.
• DO NOT sit or stand on any part of the
Cruiser
.
• DO NOT lift and/or drop the
Cruiser
as doing so may cause bodily injury to the user and irreparable
damage to the
Cruiser
.
• Play with the
Cruiser
on the floor or ground only.
• DO NOT operate this
Cruiser
during thunderstorms.
• Keep hair, fingers, loose clothing and other items away from rotating wheels of the unit.
Before going for a drive, make sure that your dolls are in place and buckled up:
1. Lift the elastic band. (Fig. 3)
2. Secure your doll in the seat under the elastic band. (Fig. 4) Ready to roll!
BEFORE YOU BEGIN
Fig. 4
IMPORTANT INFORMATION
Fig. 6
FASTEN YOUR SEAT BELTS!
1.5V AAA/LR03
1.5V AAA/LR03
An ADULT must install batteries in the
Cruiser
.
Here’s how:
1. Switch the ON/OFF switch to “OFF.” Using a
Phillips screwdriver (not included), remove
the screw and battery compartment cover
located on the bottom of the
Cruiser
. (Fig. 1)
2. Install three (3) AA alkaline batteries (not
included) making sure the (+) and (-) ends
face the proper direction as indicated inside
the battery compartment.
3. Replace the compartment cover and tighten
the screw.
An ADULT must install batteries in the Remote
Control. Here’s how:
1. Switch the ON/OFF switch to “OFF.”
Using a Phillips screwdriver (not included)
remove the screw and battery compartment
cover on the back of the Remote Control.
(Fig. 2)
2. Install two (2) AAA alkaline batteries
(not included) making sure the (+) and (-)
ends face the proper direction as indicated
inside the battery compartment. (Fig. 2)
3. Replace the compartment cover and tighten
the screw.
1.5V
A
A / LR06
1.5V
A
A / LR06
1.5V
A
A / LR06
Fig. 1
Fig. 2
Fig. 5
Fig. 3
OPERATING THE
CRUISER
REMOTE CONTROL
CRUISER
OFF
ON
ON
OFF
CAUTION:
