MFJ MFJ-561K Manual Download Page 2

Page: 2 / 6

MFJ-561K

Travel Iambic Paddle Kit

surfaces to be connected are hot. Then, feed the solder around the lead causing
the solder to wick up, wetting all exposed surfaces.

Desoldering Tips:

If you make a mistake in soldering and need to correct a

step, follow these instructions carefully. First, grasp the part to be removed with
a pair of hemostats or needle-nose pliers. Heat the solder joint until the solder
loosens and pull gently. The lead should then be able to be extracted. Repeat
this process for any other bad connections.

PARTS LIST

Your kit should contain all of the parts listed below. Please identify and
inventory each part on the checklist before you start building. If any parts are
missing or damaged, refer to the manual’s warranty section for replacement
instructions.

;

Qty

Part Description

Part Number

1 Paddle

Base

738-0561

1 Paddle

735-0561

Phillips Head Screws

654-0250S

Solder Lugs (Aluminum Tabs)

720D-0621L

2 Washers

714-0631

2 Shoulder

Washers

7145-0421N

3 Kep

Nuts

705-0440-K

Open-end 3.5 mm Stereo Cable

620-8005

1 Spacer

715B-0500S

6 Rubber

Feet

770-1162

1 Wire

Tie

745-2149

Summary of Contents for MFJ-561K







Search results

Summary of Contents for MFJ-561K

Reviews:

MFJ MFJ-561K, Manual, Page: 2 / 6

Search results

Summary of Contents for MFJ-561K

Reviews: