MFJ MFJ-415B Instruction Manual Download Page 7

MFJ-415B CW Adapter 

 

Instruction Manual 

In Case of Difficulty 

!

  Radio does not shift to CW band or perform CW functions when adapter is activated.

  

Check headers to confirm sure all pins are inserted into the adapter board. 

 

!

  Stations do not respond to your calls or do not reply to you on your frequency.  Check 

Offset 

trimpot R103 for correct setup.  To approximate the factory default, set R103 

so the arrow  points to the "R" in R103.  Then, if needed, readjust.   

 

!

 Stations report hearing a continuous carrier between keyed characters.  Check 

transceiver's 

carrier null

 adjustment (R36).  Null for minimum carrier in SSB mode.  

Carrier should be at least -40 dBc, or 40-dB down from full CW output. 

 

Technical Assistance 

If you have any problem with this unit first check the appropriate section of this manual. 
If the manual does not reference your problem or your problem is not solved by reading 
the manual, you may call 

MFJ Technical Service

 at 

601-323-0549

 or the 

MFJ Factory

 at 

601-323-5869

.  You will be best helped if you have your unit, manual and all information 

on your station handy so you can answer any questions the technicians may ask. 
 
You can also send questions by mail to MFJ Enterprises, Inc., 300 Industrial Park Road, 
Starkville, MS 39759; by Facsimile (FAX) to 601-323-6551; or by email to 
[email protected].  Send a complete description of your problem, an 
explanation of exactly how you are using your unit, and a complete description of your 
station. 
 

Summary of Contents for MFJ-415B










Reviews: