background image

 

  

 

  
  

 

Pneumatic table stapler  

TH 210 

 

 

Page: 

 

1

 

Change: 

02/2019 

ET  

   

598

 

 

Page 1 of 12     21.02.19       P:\Technik\TH_THE_210\Bedienungsanleitung\Englisch\BA TH 210 02_2019_EN.docx 

 

 

Operating Instructions 

    

Pneumatic table stapler 

TH 210 

 

  

IMPORTANT

 

 

Before the first commissioning read this manual thoroughly and completely and keep it in a safe place. 

Observe and follow the safety instructions and only use the stapling device if you are sure that you 

have completely understood all the instructions.  

Failure to comply can lead to injuries! 

 

If you have any questions, contact the manufacturer 

 

MEZGER Heftsysteme 

Saganer Straße 24 

90475 Nuremberg 

Germany 

+49 (0)911 984 94 0 

 

 

 Model

 

 
Type/description: 
 
 

Preface

 

 

For a safe operation of the stapling device it is necessary to acquire the knowledge conveyed by these 

ORIGINAL OPERATING INSTRUCTIONS

. The information is presented in brief and clear form. The 

chapters are sorted by numbers. 

 

 

Copyright

 

 

The copyright of this operation manual remains with 

MEZGER Heftsysteme GmbH 

 

 

 

See device label 

 

TH 210/2/MZ 
 

Summary of Contents for TH 210













Reviews: