background image

11

GB

PUSH HANDLE

The insertion tubes (Fig.40) can be re-
placed with push handles (Fig.41).

Fitting push handles

Tools:
Hexagonal stud wrench WW* 4–5/
32
– Pull the backrest belt off the Velcro

strips and wrap it forwards.

– Remove screw connection (A,

Fig.40).

– Remove the backrest strap.
– Remove screw connection (B,

Fig.40). – Keep hold of the insertion
tube as it will otherwise slide into the
backrest tube.

– Replace insertion tube with push han-

dle (or vice versa) and position it at
the desired hole location.

– Assemble screw connection (B,

Fig.41).

– Re-fit backrest strap.
– Assemble screw connection (A,

Fig.41).

– Re-fasten the backrest belt.

STEERING HEAD AD-

JUSTMENT

The adjustment should be car-
ried out by the specialist
dealer!

The steering heads (A, Fig.39) for bear-
ing support of the steering wheel forks
can be adjusted for an optimum driving
behaviour 90° to the driving surface by
way of the respective eccentric screw
(B., Fig.39).

Important information:

Eccentric screws to adjust the steering
head have to be secured with soluble
Loctite glue after every third adjust-
ment. – Remove grease and glue re-
mainders from the flights of the eccen-
tric screws or use new eccentric
screws alternatively.

SEAT TILT

The adjustment should be car-
ried out by the specialist
dealer!

The seat tilt is infinitely variable by con-
stant chassis geometry.
Benefits:
– High sitting stability by way of

wedge-shaped seat position via ad-
justable seat tilt.

Handling:
Tools
Hexagonal stud wrench WW* 4+5
Engineer’s wrench WW* 10
– Fold armrests onto the seat.
– Slacken the screw connection of the

rear seat-strut mount (A, Fig.37).

– Slacken the screws of the clamping

guides (B, Fig.38).

– Adjustment of seat tilt. – Position the

backrest tubes for the desired rear
seat-height.

Note:

The adjustment should be made so
that the backrest tubes protruding from
the clamping guides have the same
length.

– Tighten the screws (B, Fig.38) of the

clamping guides.

– Tighten the screw connection of the

rear seat-strut mount (A, Fig.37).

WW* = Wrench width [mm]

Summary of Contents for 2.871



























Reviews: